OBDSTAR X300 DP Key Master DP Plus C Full Version Support Auto Programming and Cluster Calibrate for Toyota Smart Key

Buy X300 DP PLUS C Full Can Get 2 Years Free Update     (Flash Sale!)  Hurry Up!!!!

Note: Our device doesn’t support  for DAIHATSU / PROTON / MAHINDRA / MARUTI /TATA/HOLDEN/LADA/PERODUA/IRAN local vehicles

Distributor Code:0086A002 or860755B1

Language:Englishonly

X300 DP Plus Register & Upgrade Guide

OBDSTAR X300 Key Master DP Plus Hardware Advantages:

1. Built-in VCI box

2. 8-inch touchscreen

3. Charge directly via OBD interface

4. Practical and high-end gift box

5. Industrial design with silicone case

6. Back bracket design:prop on the steering wheel or stand on the table

7. With 4 Toyota simulation keys (the fifth is coming soon)

8. P001 programmer: EEPROM adapter + RFID adapter + Key Renew adapter

9. Add the clip of reading SOP 8PIN EEPROM

10. C001/C002 circuit board to read and write chip data with welding

11. IMMO induction coil to detect the key induction coil failure of the vehicle.

12. Add wiring harness of ECU reading by OBD (for ECU cloning and switch activation)

OBDSTAR X300 Key Master DP Plus Software Advantages:

IMMO:

1. EEPROM

2. Renew Key

3. Key programming

4. Remote programming

Cluster Calibrate: wild vehicle coverage, pls check the carlist

Diagnosis: realize all vehicle systems diagnosis

Special Functions

TPS/ABS/EPB/DPF/TPMS/SRS Reset/Fuel Injector/Gear Learning/Battery Matching/ECU Programming/Throttle Matching/

Oil/service reset/Steering Angle Reset/Remote Manual Setting/Electronic Steering Reset/CVT Learning/value Reset

ECU Clone

1. ECU Clone, means ECU duplication.

The device copies all the data from the original vehicle ECU, and then writes all data copied into ECU with the same hardware to realize the same ECU function with the original vehicle.

2. Clone directly when replacing a new or a used ECU!

Without online matching in 4S store or removal of ECU bonding wire for reading and writing! Directly write without dismantling OBD!

3. Three features for ECU Clone:

A. Free of 4S online:

break monopoly from 4S, benefiting automobile maintenance industry

B. Simplified operation procedures: realize foolproof operation

C. Non-dismantling with zero risks: read and write data without dismantling ECU

Switch Activation Function

(Today many instruments or audio of vehicles activate secondary power supply to go into power-on status by relevant module CAN communication on the vehicle, but sometimes an instrument or an audio is separated from vehicle CANBUS network, causing startup failure when it needs to be repaired by an auto technician. This function can simulate CAN communication to activate secondary power supply, so the instrument or the audio enters into power-on status. In this way, it not only can test and verify the instrument or the audio, but also save an enormous cost for an auto technician to purchase a large number of startup platforms of various vehicles and wiring harnesses!)

Add “Help” Functions

1. including built-in testable vehicle models, upgrade announcement, features, help notes and wiring diagrams, etc.

2. Carlist and upgrade announcement, all details are available on the device

3. Customers can look up the features or uniquely support functions on the device

4.  Help notes: built-in help notes for each model or function

5. Wiring diagrams: built-in ECU wiring diagrams, more intuitionistic and convenient

TECHNICAL PARAMETER

● Operation system: Android 5.1.1

● CPU: Exynos4418  Dual Core ARM Cortex A9 1.4GHz

● Battery: 3700mA, rechargeable polymer lithium battery

● Extension memory card: 32G Micro SD (TF) card supported

● Memory capacity:1GB

● Storage capacity: 32GB

● LCD: 8.0 inch

● LCD resolution: 1280*800

● Touch screen: Capacitive touch screen

● Camera: 5 mega rear view camera

● Wi-Fi: supported

● Working temperature: -10℃  ~  55℃（14℉  ~  131℉ ）

● Storage temperature: -20℃  ~  70℃（-4℉  ~ 158℉ ）

● Weight: about 1.0 Kg

● Dimension: 254mm*174*mm*35mm

CONFIGURATIONS

A Package:

Immobilizer+Special function(EEPROM+Key Renewing)Adapter(P001 programmer+C001circuit board+C002 circuit board+W001 cable+W002 data cable+W003 data cable+Toyota smart key Emulator)+others(Ignition coil+Remote tester)

C Package:

Immobilizer+Mileage correction+Diagnosis+Special function (Oil rest +ABS+Battery matching+ECU programming+EPB+Throttle programming+Airbag rest+TPMS+Steering angle rest+OBDII+DPF+Injector code+Supension matching+Gear learning+CVT learning+EEPROM+Key renewing+ECU cloning)Adapter(P001 programmer+C001 circuit board+C002 circuit board+W001 data cable+W002 data cable+W003 data cable+Toyota smarkt key Emulator)+others(Ignition coil+Remote tester)

1. Clone ECU

Clone ECU means copy ECU, that is the OBDSTAR X300 DP Plus copies the data from the original car ECU, then write it into another same ECU hardware, so that it can achieve the same function as the original ECU.

When you want to change the new ECU or the second ECU, if you use X300 DP Plus to clone via OBD, you won’t need to go to the 4s store to do the online programming or dismantle ECU to weld, read & write.

ECU clone Pros :

No need to go to 4S shop, convenient, fast and save money.

Simplify the operating steps, even the amateur can also operate.

No need to dismantle and weld the ECU to read & write, it is zero risk to clone ECU via OBD with the X300 DP Plus.

2. Switch activation function

Nowadays, many car models’ secondary power supply of the dashboard or audio equipment needs to be activated to enter the boot status through the related module CAN.

However, when the car technician maintains the dashboard / audio equipment, the main unit is out of the CANBUS network so it maybe won’t boot. X300 DP plus ” switch activation function” can emulate the CANBUS communication to active the power supply of dashboard / Audio so that it can enter the boot status, then it will test and verify the dashboard and the Audio, also the technician can save money avoiding to purchase many the boot platform and cables of kinds of car models.

3. Adds the “Help” function including the testable car models, update notice, special features, help instruction, wiring diagram etc.

Testable car models: The user can read the testable car models and year.

Update notice: The user can read all of the update content.

Features: The user can read all of the special features and the functions that only X300 DP Plus supports.

Help instruction: Built-in the guide and instruction for each car model or function.

Wiring diagram: Built-in ECU wiring diagram, more intuitive and convenient.

4. Maintenance database: equipped with powerful database.

5. Video center: large amount of videos help users to operate device easily.

6. One Key Upgrade: built-in WIFI mode can realize application downloading and diagnostic function by one key upgrade.

7. System setting: set VCI formation, language, unit, data logging, user information etc.

8. Remote assistance: achieve remote assistance by this function.

9. Report center: record maintenance data logging and create reports during operation.

10. USB Inspection Camera (optional): Flexible and long pipe with HD camera, it can reach car interior pipeline or narrow space to have an overall inspection.

OBDSTAR X300 DP Plus Hardware Features:

1. The built-in VCI box offers more stable communication.

2. The 8″ touch screen offers better vision experience.

3. Allow the user tocharge by the OBD port of car. Not like the X300 DP 7″ Pad, which need to be 100% charged before use.

4. With specialized toolkit, high grade and practical.

5. Industrial -grade design, comes with the silicone sleeve

6. The back bracket allows the user to hang it on the steering wheel or stand on the table, which brings great convenience to the operator.

7. Comes with forToyota Lexus Emulators(The first 4 pieces are already released, and the 5th one is under development)

8. The following 3 adapters are integrated into the X300 PAD plus: EEPROM /PIC 2-in-1 adapter, RFID adapter (VW Audi 4th / 5th IMMO programming and other cars e.g Porsche, BMW, Fiat etc.) and Renew Key PCF79XX adapter.

9. Adds the clip for readingSOP 8PIN EEPROM.

10. Adds the cables forreading ECU via OBD(Used to clone ECU and active the switch).

Different among OBDSTAR X300 DP Plus C Package (Full Version), A Package and B Package:

OBDSTAR X300DP X300 DP Plus C Full Package

OBDSTAR X300 DP Plus X300 PAD2 A Package:

Immobilizer+Special function(EEPROM+Key Renewing)Adapter(P001 programmer+C001circuit board+C002 circuit board+W001 cable+W002 data cable+W003 data cable+Toyota smart key Emulator)+others(Ignition coil+Remote tester)

Why OBDSTAR X300 DP Plus is a good investment even expensive

OBDSTAR X300 DP Plus Technical Parameter:

Operation system: Android 5.1.1

CPU: Exynos4418  Dual Core ARM Cortex A9 1.4GHz

Battery: 3700mA, rechargeable polymer lithium battery

Extension memory card: 32G Micro SD (TF) card supported

Memory capacity:1GB

Storage capacity: 32GB

LCD: 8.0 inch

LCD resolution: 1280*800

Touch screen: Capacitive touch screen

Camera: 5 mega rear view camera

Wi-Fi: supported

Working temperature: -10  ~  55(14  ~  131 )

Storage temperature: -20  ~  70(-4  ~ 158 )

Weight: about 1.0 Kg

Dimension: 254mm*174*mm*35mm

OBDSTAR X300 DP Plus X300 Package List:

Key Master DP Plus Unit

Main Wire

12V2A DC Charger

for KIA-20

OBD II-16 Connector

for HAIMA-17

for HONDA-3

for HYUNDAI/KIA-10

IMMO Induction Coil

Muti-functional Jumper

P001 Programmer Unit

C001/C002 Circuit Board

W001

W002

W003

RT100

for TOYOTA Simulation Smart Keys

Configuration List/Certificate/Quick Start Guide Fold